Welcome to DU! The truly grassroots left-of-center political community where regular people, not algorithms, drive the discussions and set the standards. Join the community: Create a free account Support DU (and get rid of ads!): Become a Star Member Latest Breaking News Editorials & Other Articles General Discussion The DU Lounge All Forums Issue Forums Culture Forums Alliance Forums Region Forums Support Forums Help & Search

DIY & Home Improvement

X_Digger

(18,585 posts)

8. The tailpipe likely screws out, and you could replace it with a shorter one if need be.

Reply to WorseBeforeBetter (Reply #7)

Mon Jun 10, 2013, 11:45 AM

Jun 2013

The fittings under the sink are best done with slip fittings and nuts. You slide a plastic nut, then a plastic washer (cone side down) over the tailpipe, then slip the trap over the tailpiece and hand tighten the nut.

They make an adjustable ribbed piece that can accommodate various angles. It looks like a bendy straw.

Edit history

Please sign in to view edit histories.

Recommendations

0 members have recommended this reply (displayed in chronological order):

41 replies

= new reply since forum marked as read

Highlight:

Shortening a metal pipe... [View all] WorseBeforeBetter Jun 2013 OP

A file or a bench grinder should be fine. mbperrin Jun 2013 #1

Thanks. I hit Home Depot (and maybe Ace) tomorrow. WorseBeforeBetter Jun 2013 #3

Angle grinder with a metal cutting blade. JoeyT Jun 2013 #2

Thanks for the reply. WorseBeforeBetter Jun 2013 #4

If you want to cut more off for some reason, you can use a hacksaw or something similar. (nt) jeff47 Jun 2013 #5

I do have a couple of those. WorseBeforeBetter Jun 2013 #7

The tailpipe likely screws out, and you could replace it with a shorter one if need be. X_Digger Jun 2013 #8

Yes, that's the piece I'm now thinking needs replaced/cut... WorseBeforeBetter Jun 2013 #10

The tailpipe threads are very fine and often get seized w/ age. X_Digger Jun 2013 #11

Ah, good point... WorseBeforeBetter Jun 2013 #12

If you are worried about distorting the pipe... catnhatnh Jun 2013 #6

That's good... WorseBeforeBetter Jun 2013 #9

Disaster...starting over. WorseBeforeBetter Jul 2013 #13

Were it me, I'd go ahead and check to see if there's a cleat first. X_Digger Jul 2013 #15

So, that means... WorseBeforeBetter Jul 2013 #17

Yup, installing a cleat is a bit of a pain. X_Digger Jul 2013 #18

LOL! WorseBeforeBetter Jul 2013 #20

Now I'm the idiot... toggle bolts straight into the drywall? WorseBeforeBetter Jul 2013 #21

*nod* Since it has a pedestal, it's supported. X_Digger Jul 2013 #22

Heh heh. WorseBeforeBetter Jul 2013 #24

If it were lag bolted into a cleat, then yes, it could float above the pedestal. X_Digger Jul 2013 #25

Well, you've been very helpful... thanks again. WorseBeforeBetter Jul 2013 #27

The challenge, the frustration, and then the sense of accomplishment at a job well done? X_Digger Jul 2013 #29

Agreed. It sounds like a major PITA now, WorseBeforeBetter Jul 2013 #30

Be sure to post pictures when it's done!! n/t X_Digger Jul 2013 #31

Oh, I will... thanks again! :-) WorseBeforeBetter Jul 2013 #33

Next question -- tailpiece? WorseBeforeBetter Jul 2013 #14

It looks like you have a few pieces missing there.. X_Digger Jul 2013 #16

Hmm. WorseBeforeBetter Jul 2013 #19

The black rubbery piece goes at the bottom, not the top.. X_Digger Jul 2013 #23

Exactly. WorseBeforeBetter Jul 2013 #26

Never seen a black plastic flange, but that could just be my inexperience. X_Digger Jul 2013 #28

The flange and pop-up are oil-rubbed bronze. WorseBeforeBetter Jul 2013 #32

*nod* sounds perfect. X_Digger Jul 2013 #34

Quick and dirty. Since you only want 1/16 pack... TheMadMonk Jul 2013 #35

Oops, I missed this post last night. And I just cut... WorseBeforeBetter Jul 2013 #36

Ta-da! WorseBeforeBetter Aug 2013 #37

Awesome! n/t X_Digger Aug 2013 #38

I'm so freakin' happy to be out of that bathroom. WorseBeforeBetter Aug 2013 #39

Bask in the glory of a project well done. X_Digger Aug 2013 #40

Heh heh. WorseBeforeBetter Aug 2013 #41